Arksine f8649b4ba9 stm32: Wait for setup complete to enable ep0 rx in usbotg.c ...

Endpoint 0 OUT needs to NAK everything until the core signals that the
setup stage is complete.

Signed-off-by: Eric Callahan <arksine.code@gmail.com>
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>

2020-05-03 12:00:47 -04:00

..

atsam

atsam: Fix typo causing chipid to not be fully read

2019-11-27 14:33:20 -05:00

atsamd

atsamd: Enable chipid as usb serial number

2019-11-25 19:30:31 -05:00

avr

avr: implement i2c_read

2020-01-13 22:29:50 -05:00

generic

armcm_boot: Additional code for broken bootloaders

2020-03-04 19:50:56 -05:00

linux

linux: Adapt servo0 channels for beagleboard kernel 4.14.108-ti (#2746)

2020-05-03 11:24:42 -04:00

lpc176x

lpc176x: Add support for additional i2c buses

2020-04-21 16:11:39 -04:00

pru

pru: The TMR_CNT is cleared by writing all ones

2019-03-31 13:48:50 -04:00

simulator

simulator: Wrap code to 80 columns

2019-02-27 14:20:15 -05:00

stm32

stm32: Wait for setup complete to enable ep0 rx in usbotg.c

2020-05-03 12:00:47 -04:00

adccmds.c

adccmds: Run gpio_adc_setup() before oid_alloc()

2019-01-13 11:03:30 -05:00

basecmd.c

basecmd: No need for finalize_config command to send "config" response

2020-02-20 12:01:21 -05:00

basecmd.h

spicmds: Rework spi config commands

2019-08-06 18:56:53 -04:00

buttons.c

buttons: initialize mcu buttons based on inverted state

2019-07-05 20:01:07 -04:00

byteorder.h

byteorder: Add a header file defining common byteswap functions

2018-05-21 09:44:40 -04:00

command.c

command: Wait to send ack until after processing commands

2018-05-28 10:43:40 -04:00

command.h

buildcommands: Match DECL_X names to the actual C macro names

2019-08-22 13:26:30 -04:00

compiler.h

compiler.h: Check if __aligned and __section macros are already defined

2016-06-13 23:18:59 -04:00

ctr.h

ctr: Encode negative integers in normal hex notation

2019-08-22 13:06:44 -04:00

debugcmds.c

debugcmds: Add support for reading/writing 32bit values

2019-02-07 11:50:14 -05:00

endstop.c

endstop: Rename mcu end_stop commands to endstop

2019-07-12 08:10:53 -04:00

gpiocmds.c

gpiocmds: Specify soft pwm duration in clock ticks

2019-05-26 11:09:32 -04:00

i2ccmds.c

avr: implement i2c_read

2020-01-13 22:29:50 -05:00

initial_pins.c

initial_pins: Add ability to configure output pins at mcu startup

2019-03-17 20:56:25 -04:00

initial_pins.h

initial_pins: Add ability to configure output pins at mcu startup

2019-03-17 20:56:25 -04:00

Kconfig

stm32f0: Remove hal based stm32f0 implementation

2020-01-14 17:08:01 -05:00

lcd_hd44780.c

lcd_hd44780: Minor change to timing delays

2019-11-26 09:49:43 -05:00

lcd_st7920.c

lcd_st7920: Add brief delay around gpio toggle calls on fast MCUs

2019-08-10 11:45:15 -04:00

Makefile

initial_pins: Only build when CONFIG_HAVE_GPIO is enabled

2019-07-24 01:09:45 -04:00

neopixel.c

neopixel: Make sure there is a minimum low duration after a long pulse

2020-04-21 13:12:56 -04:00

pwmcmds.c

pwmcmds: allow 16-bit resolution

2019-04-05 19:02:48 -04:00

sched.c

sched: Force sched_try_shutdown to be inlined

2018-10-13 11:47:00 -04:00

sched.h

pru: Support config_reset command to manually reset mcu

2017-09-03 23:16:38 -04:00

spi_software.c

spi_software: Remove unused include file

2019-08-17 13:49:03 -04:00

spi_software.h

spi_software: Implementation of software spi

2019-02-13 11:52:20 -05:00

spicmds.c

spicmds: Rework spi config commands

2019-08-06 18:56:53 -04:00

spicmds.h

spicmds: Rework spi config commands

2019-08-06 18:56:53 -04:00

stepper.c

stepper: Add some comments on s->position tracking

2020-03-04 14:30:41 -05:00

stepper.h

stepper: Introduce stepper_get_position command and remove from endstop.c

2017-03-09 14:54:52 -05:00

thermocouple.c

thermocouple: Define thermocouple types using enumerations

2019-03-17 19:38:18 -04:00

tmcuart.c

tmcuart: Fix typo in function name

2019-09-01 14:56:09 -04:00